Standard SLC-12DR | 5-Stage Lockformer with Flanger - STANDARD Direct

STANDARD SLC-12DR 5-Stage Lockformer with Flanger

*Excludes Local Taxes*

*Products are built on order, general delivery is 8~16weeks and include Sea Freight to most ports

Description

Standard SLC-12DR 5-Stage Lock former with Flanger and 1.2mm Material Capacity:

A 5-stage Lockformer with Flanger is a type of metal forming machine that can process sheet metal with a maximum material capacity of 1.2mm. The "5-stage" refers to the number of processing steps that the machine can perform in one cycle, which is typically: feeding, forming, cutting, notching, and flanging. The "Flanger" function allows for the creation of flange edges on metal sheets. These machines are commonly used in the HVAC, roofing, and metal fabrication industries to produce various components such as ductwork, roof panels, and flashing.

Main Features:

  • Pittsburg lock
  • Standing seam
  • Drive cleat
  • Single hem (Right angle flange)
  • Double hem
  • Elbow seam (Flange attachment)
Specifications
  • Roll forming Station - 8
  • Capacity - 102mm = 4.0157 inches mild steel
  • Motor - 1.5kW = 2.0119 hp
  • Working Height - 810mm = 31.8898 inches
  • Dimensions - 1050x580x880mm = 41.3386x22.8346x34.6457 inches
  • Weight - 230kg = 507.063 lbs
Delivery

Delivery is 8-12 Weeks from Deposit


How to use a 5-Stage Lockformer

To use a 5-stage Lockformer with Flanger and 1.2mm material capacity, you would follow these general steps:

  1. Load the metal sheet: The metal sheet is loaded into the machine and clamped into place.

  2. Adjust settings: Adjust the machine settings to match the specific requirements of your project. This may include setting the speed, depth of the forming, and cutting parameters.

  3. Run a test: Run a test on a scrap piece of metal to make sure the machine is set up correctly and to check the quality of the final product.

  4. Begin processing: Start the machine and begin processing the metal sheet. The machine will perform all five stages in one cycle: feeding, forming, cutting, notching, and flanging.

  5. Inspect the final product: After the machine has finished processing, inspect the final product to make sure it meets the desired specifications.

Note: Operating a 5-stage Lockformer with Flanger requires proper training and safety precautions should be followed at all times. Before using the machine, it is important to read and understand the operator's manual and any relevant safety guidelines.

Description

Standard SLC-12DR 5-Stage Lock former with Flanger and 1.2mm Material Capacity:

A 5-stage Lockformer with Flanger is a type of metal forming machine that can process sheet metal with a maximum material capacity of 1.2mm. The "5-stage" refers to the number of processing steps that the machine can perform in one cycle, which is typically: feeding, forming, cutting, notching, and flanging. The "Flanger" function allows for the creation of flange edges on metal sheets. These machines are commonly used in the HVAC, roofing, and metal fabrication industries to produce various components such as ductwork, roof panels, and flashing.

Main Features:

  • Pittsburg lock
  • Standing seam
  • Drive cleat
  • Single hem (Right angle flange)
  • Double hem
  • Elbow seam (Flange attachment)
Specifications
  • Roll forming Station - 8
  • Capacity - 102mm = 4.0157 inches mild steel
  • Motor - 1.5kW = 2.0119 hp
  • Working Height - 810mm = 31.8898 inches
  • Dimensions - 1050x580x880mm = 41.3386x22.8346x34.6457 inches
  • Weight - 230kg = 507.063 lbs
Delivery

Delivery is 8-12 Weeks from Deposit

How to use a 5-Stage Lockformer

To use a 5-stage Lockformer with Flanger and 1.2mm material capacity, you would follow these general steps:

  1. Load the metal sheet: The metal sheet is loaded into the machine and clamped into place.

  2. Adjust settings: Adjust the machine settings to match the specific requirements of your project. This may include setting the speed, depth of the forming, and cutting parameters.

  3. Run a test: Run a test on a scrap piece of metal to make sure the machine is set up correctly and to check the quality of the final product.

  4. Begin processing: Start the machine and begin processing the metal sheet. The machine will perform all five stages in one cycle: feeding, forming, cutting, notching, and flanging.

  5. Inspect the final product: After the machine has finished processing, inspect the final product to make sure it meets the desired specifications.

Note: Operating a 5-stage Lockformer with Flanger requires proper training and safety precautions should be followed at all times. Before using the machine, it is important to read and understand the operator's manual and any relevant safety guidelines.

*Information shown may differ or change without warning*

Product Search